blob: 632bbd72606b1f50324ac51e96a6d820e6ea92dc (
plain) (
tree)
|
|
/***************************************************************************
* Example sketch for the ADS1115_WE library
*
* This sketch shows how to use the ADS1115 module with the TinyWireM library:
* https://github.com/adafruit/TinyWireM
* This allows you to run the ADS1115_WE library on an ATtiny85, for example.
*
* For this specific sketch you also need library Tiny4KOLED to display the
* measured values on a SSD1306 OLED display:
* https://github.com/datacute/Tiny4kOLED
*
* Further information can be found on:
* https://wolles-elektronikkiste.de/ads1115 (German)
* https://wolles-elektronikkiste.de/en/ads1115-a-d-converter-with-amplifier (English)
*
***************************************************************************/
/* !!!! IN ORDER TO USE TinyWireM YOU NEED TO UNCOMMENT #define USE_TINY_WIRE_M_ !!!!
* !!!! IN ADS1115_config.h WHICH YOU FIND IN THE libraries/ADS1115_WE/src FOLDER !!!! !!!!
*/
#include <TinyWireM.h>
#include <Tiny4kOLED.h>
#include<ADS1115_WE.h>
#define ADS1115_I2C_ADDR 0x48
uint8_t width = 128;
uint8_t height = 64;
/* There are two ways to create your ADS1115_WE object:
* ADS1115_WE adc = ADS1115_WE() -> uses Wire / I2C Address = 0x48
* ADS1115_WE adc = ADS1115_WE(I2C_ADDRESS) -> uses Wire / I2C_ADDRESS
*/
ADS1115_WE adc = ADS1115_WE(ADS1115_I2C_ADDR);
void setup() {
TinyWireM.begin();
oled.begin(width, height, sizeof(tiny4koled_init_128x64br), tiny4koled_init_128x64br);
oled.clear();
oled.setFont(FONT6X8);
oled.on();
if(!adc.init()){
oled.print("ADS1115 not connected");
while(1){}
}
else{
oled.print("ADS1115 connected");
delay(1000);
oled.clear();
}
/* Set the voltage range of the ADC to adjust the gain
* Please note that you must not apply more than VDD + 0.3V to the input pins!
*
* ADS1115_RANGE_6144 -> +/- 6144 mV
* ADS1115_RANGE_4096 -> +/- 4096 mV
* ADS1115_RANGE_2048 -> +/- 2048 mV (default)
* ADS1115_RANGE_1024 -> +/- 1024 mV
* ADS1115_RANGE_0512 -> +/- 512 mV
* ADS1115_RANGE_0256 -> +/- 256 mV
*/
adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range
/* Set the inputs to be compared
*
* ADS1115_COMP_0_1 -> compares 0 with 1 (default)
* ADS1115_COMP_0_3 -> compares 0 with 3
* ADS1115_COMP_1_3 -> compares 1 with 3
* ADS1115_COMP_2_3 -> compares 2 with 3
* ADS1115_COMP_0_GND -> compares 0 with GND
* ADS1115_COMP_1_GND -> compares 1 with GND
* ADS1115_COMP_2_GND -> compares 2 with GND
* ADS1115_COMP_3_GND -> compares 3 with GND
*/
adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channel
/* Set number of conversions after which the alert pin asserts
* - or you can disable the alert
*
* ADS1115_ASSERT_AFTER_1 -> after 1 conversion
* ADS1115_ASSERT_AFTER_2 -> after 2 conversions
* ADS1115_ASSERT_AFTER_4 -> after 4 conversions
* ADS1115_DISABLE_ALERT -> disable comparator / alert pin (default)
*/
//adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); //uncomment if you want to change the default
/* Set the conversion rate in SPS (samples per second)
* Options should be self-explaining:
*
* ADS1115_8_SPS
* ADS1115_16_SPS
* ADS1115_32_SPS
* ADS1115_64_SPS
* ADS1115_128_SPS (default)
* ADS1115_250_SPS
* ADS1115_475_SPS
* ADS1115_860_SPS
*/
// adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default
/* Set continuous or single shot mode:
*
* ADS1115_CONTINUOUS -> continuous mode
* ADS1115_SINGLE -> single shot mode (default)
*/
adc.setMeasureMode(ADS1115_CONTINUOUS); //comment line/change parameter to change mode
/* Choose maximum limit or maximum and minimum alert limit (window) in Volt - alert pin will
* assert when measured values are beyond the maximum limit or outside the window
* Upper limit first: setAlertLimit_V(MODE, maximum, minimum)
* In max limit mode the minimum value is the limit where the alert pin assertion will be
* cleared (if not latched)
*
* ADS1115_MAX_LIMIT
* ADS1115_WINDOW
*
*/
//adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default
/* Enable or disable latch. If latch is enabled the alert pin will assert until the
* conversion register is read (getResult functions). If disabled the alert pin assertion will be
* cleared with next value within limits.
*
* ADS1115_LATCH_DISABLED (default)
* ADS1115_LATCH_ENABLED
*/
//adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default
/* Sets the alert pin polarity if active:
*
* ADS1115_ACT_LOW -> active low (default)
* ADS1115_ACT_HIGH -> active high
*/
//adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default
/* With this function the alert pin will assert, when a conversion is ready.
* In order to deactivate, use the setAlertLimit_V function
*/
//adc.setAlertPinToConversionReady(); //uncomment if you want to change the default
}
/* If you change the compare channels you can immediately read values from the conversion
* register, although they might belong to the former channel if no precautions are taken.
* It takes about the time needed for two conversions to get the correct data. In single
* shot mode you can use the isBusy() function to wait for data from the new channel. This
* does not work in continuous mode.
* To solve this issue the library adds a delay after change of channels if you are in contunuous
* mode. The length of the delay is adjusted to the conversion rate. But be aware that the output
* rate will be much lower that the conversion rate if you change channels frequently.
*/
void loop() {
float voltage = 0.0;
adc.setCompareChannels(ADS1115_COMP_0_GND);
voltage = adc.getResult_V();
oled.setCursor(0,0);
oled.print("Channel 0 [V]: ");
oled.print(voltage);
oled.clearToEOL();
adc.setCompareChannels(ADS1115_COMP_1_GND);
voltage = adc.getResult_V();
oled.setCursor(0,2);
oled.print("Channel 1 [V]: ");
oled.print(voltage);
oled.clearToEOL();
adc.setCompareChannels(ADS1115_COMP_2_GND);
voltage = adc.getResult_V();
oled.setCursor(0,4);
oled.print("Channel 2 [V]: ");
oled.print(voltage);
oled.clearToEOL();
adc.setCompareChannels(ADS1115_COMP_3_GND);
voltage = adc.getResult_V();
oled.setCursor(0,6);
oled.print("Channel 3 [V]: ");
oled.print(voltage);
oled.clearToEOL();
delay(2000);
}
|
