1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
|
---
title: Technicolor AFM0002
has_children: false
layout: default
parent: Technicolor
alias: HiSense LTE3415-SCA+
---
# Hardware Specifications
| | |
| ---------------- | ----------------------------------------------- |
| Vendor/Brand | Technicolor |
| Model | AFM0002TIM/FWB/WND |
| ODM | HiSense |
| ODM Product Code | LTE3415-SCA+ |
| Chipset | Realtek RTL9601B |
| Flash | 32MB |
| RAM | 16MB |
| System | Linux (Luna SDK 1.9) |
| HSGMII | No |
| Optics | SC/APC |
| IP address | 192.168.2.1 / 169.0.0.1 |
| Web Gui | Can be enabled, user `admin`, password `system` |
| SSH | ✅ user `admin`, password `system` |
| Telnet | |
| Serial | ✅ |
| Serial baud | 115200 |
| Serial encoding | 8-N-1 |
| Form Factor | miniONT SFP |
| Multicast | ✅ |
{% include image.html file="afm0002tim.jpg" alt="AFM0002TIM" caption="AFM0002TIM" %}
{% include image.html file="afm0002fwb.jpg" alt="AFM0002FWB" caption="AFM0002FWB" %}
## Serial
The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be accessed from the top surface. To accept TX line commands, the GND of the TTL adapter should be attached to the stick's shield:
{% include image.html file="ont-leox-lxt-010s-h_ttl.jpg" alt="Technicolor AFM0002 TTL Pinout" caption="Technicolor AFM0002 TTL Pinout" %}
{% include alert.html content="Some USB TTL adapters label TX and RX pins the other way around: try to swap them if the connection doesn't work." alert="Note" icon="svg-warning" color="yellow" %}
## Hardware Revisions
- AFM0002TIM (IP address: 192.168.2.1)
- AFM0002FWB (IP address: 169.0.0.1)
- AFM0002WND (IP address: 169.0.0.1)
{% include alert.html content="The version used to obtain the info shown on this page is the AFM0002TIM" alert="Info" icon="svg-info" color="blue" %}
{% include alert.html content="The AFM0002FWB can be transformed into AFM0002TIM. Usually AFM0002FWBs have older software." alert="Warning" icon="svg-warning" color="red" %}
## List of software versions
- V1.7.6-170626 (FWB & WND)
- V1_7_8_180122
- V1_7_8_180725
- V1_7_8_181123
- V1_7_8_210412
- V1_7_8_210928
## List of partitions
| dev | size | erasesize | name |
| ----- | -------- | --------- | --------------- |
| mtd0 | 00040000 | 00001000 | "boot" |
| mtd1 | 00002000 | 00001000 | "env" |
| mtd2 | 00002000 | 00001000 | "env2" |
| mtd3 | 0003c000 | 00001000 | "config" |
| mtd4 | 00300000 | 00001000 | "k0" |
| mtd5 | 004c0000 | 00001000 | "r0" |
| mtd6 | 00300000 | 00001000 | "k1" |
| mtd7 | 004c0000 | 00001000 | "r1" |
| mtd8 | 00001000 | 00001000 | "Partition_008" |
| mtd9 | 00001000 | 00001000 | "Partition_009" |
| mtd10 | 00001000 | 00001000 | "Partition_010" |
| mtd11 | 00001000 | 00001000 | "Partition_011" |
| mtd12 | 00300000 | 00001000 | "linux" |
| mtd13 | 004c0000 | 00001000 | "rootfs" |
This stick supports dual boot.
`k0` and `r0` respectively contain the kernel and firmware of the first image, `k1` and `r1` the kernel and firmware of the second one
{% include_relative ont-luna-sdk-useful-commands.md flash='/etc/scripts/flash' ploam='ascii' lastgoodHs=true %}
## Enabling the Web UI
```sh
# /bin/iptables -D INPUT -p tcp --dport 80 -j DROP
```
## Transfering files from/to the stick
Works with binary files too, just run md5sum on source and destination to make sure you are not corrupting anything...
From the stick to the PC:
```sh
# ssh admin@192.168.2.1 "cat /tmp/omcilog" > omcilog.log
```
From the PC to the stick:
```sh
# cat lastgood.xml | ssh admin@192.168.2.1 "cat > /var/config/lastgood.xml"
```
{% include alert.html content="If a Windows system is used replace type with cat and run the commands from cmd (not Powershell)" alert="Info" icon="svg-info" color="blue" %}
## Extracting and repacking the rootfs
{% include alert.html content="Make sure you run both commands as root, otherwise you might get a damaged rootfs image" alert="Warning" icon="svg-warning" color="red" %}
```sh
# unsquashfs mtd5.bin
# mksquashfs squashfs-root rootfs -b 131072 -comp lzma -no-recovery
```
## Flashing a new rootfs
{% include alert.html content="Only the inactive image can be flashed, change sw_versionX and sw_commit X based on the bank you have flashed" alert="Info" icon="svg-info" color="blue" %}
So mtd4/5 if you are on image1, mtd6/7 if you are on image0.
The following commands are used to flash a new rootfs to image1 and then boot to it
```sh
# flash_eraseall /dev/mtd7
# cat /tmp/rootfs.new > /dev/mtd7
# nv setenv sw_version1 NEW_SOFTWARE_VERSION
# nv setenv sw_commit 1
# reboot
```
# Low Level Modding
{% include alert.html content="This section is based on the `V1_7_8_210412` version of the stick's firmware " alert="Info" icon="svg-info" color="blue" %}
## Adding support to configurable SW and HW versions, Vendor ID and much more
`/etc/scripts/flash` can be flashed in order to add support for some variables implemented in `omci_app` but removed from `xmlconfig`. The patch is below (change the values to suit your needs)
```patch
--- squashfs-root/etc/scripts/flash 2021-09-28 10:38:52.000000000 +0200
+++ squashfs-root.new/etc/scripts/flash 2022-08-04 00:00:29.769605000 +0200
@@ -62,7 +62,26 @@
if [ `echo $para | egrep $specific_mib_patten` ]; then
/bin/xmlconfig -g $para | sed -r "s/$rename_mib_name+/$2/g" | sed -r "s/,+//g"
else
- /bin/xmlconfig -g $para | sed -r "s/$rename_mib_name+/$2/g"
+ case "$para" in
+ "OMCI_EQID")
+ echo "$para=MY_EQID"
+ ;;
+ "OMCI_VENDOR_ID")
+ echo "$para=MY_VENDOR"
+ ;;
+ "OMCI_SW_VER1")
+ echo "$para=MY_SW_VER1"
+ ;;
+ "OMCI_SW_VER2")
+ echo "$para=MY_SW_VER2"
+ ;;
+ "OMCI_ONT_VER")
+ echo "$para=MY_HW_VER"
+ ;;
+ *)
+ /bin/xmlconfig -g $para | sed -r "s/$rename_mib_name+/$2/g"
+ ;;
+ esac
fi
if [ "$?" = "0" ]; then
exit 0
```
## Increasing the length of the software version from 13 to 14 characters
`omci_app` has an hard-coded limit of 13 characters for the software version, which is too low. We can binary patch it to increase it to 14 (or more, if you dare/need)
```
JVhEWjAwNCUAAAAIAAgACAAAAAAAAAAAAAAAAAAAAABvbWNpX2FwcG9tY2lfYXBwH4sIAAAAAAAA
AwMAAAAAAAAAAAAfiwgAAAAAAAADY2BoYGZgYFjh9Uq/aNcZQdXsOh3R5ktr/fd0sTEwcuTnJmfG
JxYUYJVlZGAA0gCHsMK2QQAAAAAAAEQlWERaMDA0JQ==
```
Save it as `omci_app.xdelta.base64`, then run:
```sh
# base64 -d omci_app.xdelta.base64 > omci_app.xdelta
# xdelta patch omci_app.xdelta bin/omci_app bin/omci_app.new
# mv bin/omci_app.new bin/omci_app
```
For reference, the patch changes the follwing section of the omci_app:
```diff
-00408c24 24 05 00 0e li a1,0xe
+00408c24 24 05 00 0f li a1,0xf
-00408cf0 24 05 00 0f li a1,0xe
+00408cf0 24 05 00 0f li a1,0xf
```
(It's inside the function referencing the string `OMCI_SW_VER1`)
The original file md5sum is: `4aea2f72bacc11256b7e2c1583d2ad4f`
The patched file md5sum is: `da20327c4c002e4c27f82f6ee63dbc1a`
## Enabling PLOAM logging
```sh
/etc/scripts/flash set OMCI_DBGLVL 1
/etc/scripts/flash set OMCI_DBGLOGFILE 1
reboot
/bin/omcicli set logfile 1 ffffffff
```
1. The binary log will be placed inside: `/tmp/omcilog`
2. You can convert it into a .pcap file using [omcilog2pcap](https://github.com/hack-gpon/omcilog2pcap)
3. You can then open it with Wireshark by installing the OMCI plugin from [GitHub](https://github.com/hack-gpon/omci-wireshark-dissector)
If you want to log everything since the stick boots, you can create a custom rootfs. Place the last command inside `etc/runomci.sh` as the last line of the file
# Known Bugs
# Miscellaneous Links
- [omcilog2pcap](https://github.com/hack-gpon/omcilog2pcap)
|
