1 files changed, 0 insertions, 107 deletions
diff --git a/Heimdall/Win32/README.txt b/Heimdall/Win32/README.txt
deleted file mode 100644
index 683e34a..0000000
--- a/Heimdall/Win32/README.txt
+++ /dev/null
@@ -1,107 +0,0 @@
-Heimdall (c) 2010 Benjamin Dobell, Glass Echidna
-http://www.glassechidna.com.au/products/heimdall/
-
-DISCLAIMER:
-
-    This software attempts to flash your Galaxy S device. The very nature of
-    flashing is dangerous. As with all flashing software, Heimdall has the
-    potential to damage (brick) your phone if not used carefully. If you're
-    concerned, don't use this software. Flashing ROMs onto your phone may also
-    void your warranty. I am not responsible for the result of your actions.
-
-
-
-These instructions were written for Windows Vista / Server 2008 however the producedure
-should be essentially the same for all supported versions of Windows (XP onwards). 
-
-Driver Installation Instructions:
-
-    1. Put your Samsung Galaxy S into download mode and plug it in.
-
-    2. Run zadig.exe included in the Drivers subdirectory.
-
-    3. From the menu chose Options -> List All Devices.
-
-    4. From the USB Device list chose "Samsung USB Composite DEvice".
-
-    5. Press "Install Driver", click "Yes" to the prompt and if you receive
-       a message about being unable to verify the publisher of the driver
-       click "Install this driver software anyway".
-
-    6. Done
-
-
-Driver Uninstallation Instructions:
-
-    1. Put your Samsung Galaxy S into download mode by holding Volume Down + Home + Power.
-
-    2. Plug your phone into your PC.
-
-    3. Open up Device Manager on your PC (Control Panel -> System -> Device Manager).
-
-    4. Under Universal Serial Bus Controllers right click on "Heimdall Galaxy S Driver" and chose Properties.
-
-    5. Go to the Driver tab and select Update Driver.
-
-    6. Chose to browse your computer for the driver.
-
-    7. Chose to pick from a list of devices drivers on your computer.
-
-    8. Pick the original Samsung Composite driver, press next and then follow the prompts.
-
-    9. Done
-
-
-
-Flashing Firmware with Heimdall Frontend:    
-
-    1. Fully charge your device (use the wall charger as it's faster).
-
-    2. Download a decrypted Samsung Galaxy S ROM and extract it to a directory.
-
-    3. If the ROM is provided as one of more archives (nested or otherwise),
-       extract them all to the same location.
-
-       NOTE: If you want to use the CSC then extract it last.
-
-    3. Open Heimdall Frontend.
-
-    4. Put your Galaxy S device into download mode and plug it in.
-
-    5. For each file you wish to flash use "Browse" to select the file.
-
-    6. Press "Start".
-
-    7. Heimdall Frontend will display the progress and inform you when the
-       flash is complete.
-
-
-
-Flashing Firmware from Command Prompt:
-	
-    1. Fully charge your phone (use the wall charger as it's faster).
-
-    2. Download a decrypted Samsung Galaxy S ROM and extract it to a directory.
-
-    3. If the ROM is provided as one of more archives (nested or otherwise),
-       extract them all to the same location.
-
-       NOTE: If you want to use the CSC then extract it last.
-
-    4. Put your Galaxy S device into download mode and plug it in..
-
-    5. Open command prompt and navigate to the directory where you extracted the
-       ROM files.
-
-    6. Type the following to list all the functionality Heimdall supports:
-
-            heimdall help
-
-    7. Use the instructions to manually enter a command with all the files you
-       want to flash.
-
-       Here is an example that does a full flash and repartition:
-		
-            heimdall flash --repartition --pit s1_odin_20100512.pit --factoryfs factoryfs.rfs --cache cache.rfs --dbdata dbdata.rfs --primary-boot boot.bin --secondary-boot Sbl.bin --param param.lfs --kernel zImage --modem modem.bin
-
-    8. Done