diff options
Diffstat (limited to 'src')
| -rw-r--r-- | src/ADS1115_WE.h | 105 |
1 files changed, 95 insertions, 10 deletions
diff --git a/src/ADS1115_WE.h b/src/ADS1115_WE.h index 4af25b1..c5a269a 100644 --- a/src/ADS1115_WE.h +++ b/src/ADS1115_WE.h @@ -2,17 +2,17 @@ * * This is a library for the ADS1115 A/D Converter * - * You'll find several example sketches which should enable you to use the library. + * You'll find several example sketches which should enable you to use the library. * * You are free to use it, change it or build on it. In case you like it, it would * be cool if you give it a star. * * If you find bugs, please inform me! - * + * * Written by Wolfgang (Wolle) Ewald * https://wolles-elektronikkiste.de * - * + * ******************************************************************************/ #ifndef ADS1115_WE_H_ @@ -30,7 +30,7 @@ #define ADS1115_CONV_REG 0x00 //Conversion Register #define ADS1115_CONFIG_REG 0x01 //Configuration Register #define ADS1115_LO_THRESH_REG 0x02 //Low Threshold Register -#define ADS1115_HI_THRESH_REG 0x03 //High Threshold Register +#define ADS1115_HI_THRESH_REG 0x03 //High Threshold Register /* other */ #define ADS1115_REG_FACTOR 32768 @@ -49,7 +49,7 @@ typedef enum ADS1115_LATCH { } latch; typedef enum ADS1115_ALERT_POL { - ADS1115_ACT_LOW = 0x0000, + ADS1115_ACT_LOW = 0x0000, ADS1115_ACT_HIGH = 0x0008 } alertPol; @@ -102,28 +102,113 @@ typedef enum ADS1115_STATUS_OR_START{ class ADS1115_WE { -public: +public: ADS1115_WE(int addr); - ADS1115_WE(); //sets default I2C Address 0x48 - + ADS1115_WE(); // uses default I2C Address 0x48 + void reset(); bool init(); + + /* Set number of conversions after which the alert pin will be active + * - or you can disable the alert + * + * ADS1115_ASSERT_AFTER_1 -> after 1 conversion + * ADS1115_ASSERT_AFTER_2 -> after 2 conversions + * ADS1115_ASSERT_AFTER_4 -> after 4 conversions + * ADS1115_DISABLE_ALERT -> disable comparator // alert pin (default) + */ void setAlertPinMode(ADS1115_COMP_QUE mode); + + /* Enable or disable latch. If latch is enabled the alarm pin will be active until the + * conversion register is read (getResult functions). If disabled the alarm pin will be + * deactivated with next value within limits. + * + * ADS1115_LATCH_DISABLED (default) + * ADS1115_LATCH_ENABLED + */ void setAlertLatch(ADS1115_LATCH latch); + + /* Sets the alert pin polarity if active: + * + * Enable or disable latch. If latch is enabled the alarm pin will be active until the + * conversion register is read (getResult functions). If disabled the alarm pin will be + * deactivated with next value within limits. + * + * ADS1115_ACT_LOW -> active low (default) + * ADS1115_ACT_HIGH -> active high + */ void setAlertPol(ADS1115_ALERT_POL polarity); + + /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will + * be active when measured values are beyond the maximum limit or outside the window + * Upper limit first: setAlertLimit_V(MODE, maximum, minimum) + * In max limit mode the minimum value is the limit where the alert pin will be deactivated (if + * not latched) + * + * ADS1115_MAX_LIMIT + * ADS1115_WINDOW + */ void setAlertModeAndLimit_V(ADS1115_COMP_MODE mode, float hithres, float lothres); + + /* Set the conversion rate in SPS (samples per second) + * Options should be self-explaining: + * + * ADS1115_8_SPS + * ADS1115_16_SPS + * ADS1115_32_SPS + * ADS1115_64_SPS + * ADS1115_128_SPS (default) + * ADS1115_250_SPS + * ADS1115_475_SPS + * ADS1115_860_SPS + */ void setConvRate(ADS1115_CONV_RATE rate); + + /* Set continous or single shot mode: + * + * ADS1115_CONTINOUS -> continous mode + * ADS1115_SINGLE -> single shot mode (default) + */ void setMeasureMode(ADS1115_MEASURE_MODE mode); + + /* + * Set the voltage range of the ADC to adjust the gain + * Please note that you must not apply more than VDD + 0.3V to the input pins! + * + * ADS1115_RANGE_6144 -> +/- 6144 mV + * ADS1115_RANGE_4096 -> +/- 4096 mV + * ADS1115_RANGE_2048 -> +/- 2048 mV (default) + * ADS1115_RANGE_1024 -> +/- 1024 mV + * ADS1115_RANGE_0512 -> +/- 512 mV + * ADS1115_RANGE_0256 -> +/- 256 mV + */ void setVoltageRange_mV(ADS1115_RANGE range); + + /* Set the inputs to be compared + * + * ADS1115_COMP_0_1 -> compares 0 with 1 (default) + * ADS1115_COMP_0_3 -> compares 0 with 3 + * ADS1115_COMP_1_3 -> compares 1 with 3 + * ADS1115_COMP_2_3 -> compares 2 with 3 + * ADS1115_COMP_0_GND -> compares 0 with GND + * ADS1115_COMP_1_GND -> compares 1 with GND + * ADS1115_COMP_2_GND -> compares 2 with GND + * ADS1115_COMP_3_GND -> compares 3 with GND + */ void setCompareChannels(ADS1115_MUX mux); + bool isBusy(); void startSingleMeasurement(); float getResult_V(); float getResult_mV(); + + /* With this function the alert pin will be active, when a conversion is ready. + * In order to deactivate, use the setAlertLimit_V function + */ void setAlertPinToConversionReady(); void clearAlert(); - - + + private: uint16_t voltageRange; ADS1115_MEASURE_MODE deviceMeasureMode; |