diff options
Diffstat (limited to '')
| -rw-r--r-- | _ont/ont-huawei-ma5671a-fs-mod.md | 27 |
1 files changed, 14 insertions, 13 deletions
diff --git a/_ont/ont-huawei-ma5671a-fs-mod.md b/_ont/ont-huawei-ma5671a-fs-mod.md index 7b04002..2d43ca8 100644 --- a/_ont/ont-huawei-ma5671a-fs-mod.md +++ b/_ont/ont-huawei-ma5671a-fs-mod.md @@ -11,20 +11,20 @@ layout: default Flash the firmware image to image0 or image1 via [SSH](/ont-huawei-ma5671a/#flashing-a-new-rootfs-via-ssh) or via [TTL serial](/ont-huawei-ma5671a-ymodem) as usual. -After the flash it is absolutely necessary to connect to the SFP via telnet using the IP 192.168.1.10: +After flashing, it is absolutely necessary to connect to the SFP via telnet using the IP 192.168.1.10: ```sh telnet 192.168.1.10 ``` -Once connected via telnet to the SFP, execute the following commands, it will be necessary to wait a few minutes until the end of the automatic procedure: +Once connected via telnet to the SFP, execute the following commands. Then wait a few minutes until the end of the automatic procedure: ```sh firstboot reboot ``` -Remember that with each flash of this firmware it is always necessary to perform the procedure described above, otherwise the SFP will not work! +Performing the procedure described above is necessary after each flash of this firmware, otherwise the SFP will not work! # Login info @@ -40,17 +40,17 @@ Remember that with each flash of this firmware it is always necessary to perform # GPON ONU status -## Get the operational status of the ONU +## Getting the operational status of the ONU ```sh onu ploam_state_get ``` -## Get optical laser status +## Getting optical laser status ```sh otop -g s ``` -## Get information of the OLT vendor +## Getting information of the OLT vendor ```sh omci_pipe.sh meg 131 0 ``` @@ -59,14 +59,14 @@ omci_pipe.sh meg 131 0 ```sh omci_pipe.sh meg MIB_IDX ME_IN ``` -Where `MIB_IDX` is the MIB ID and the `ME_IN` is the ME instance number +Where `MIB_IDX` is the MIB ID and `ME_IN` is the ME instance number. -## Get VLAN table rule +## Getting VLAN table rule ```sh gtop -g "GPE VLAN rule" ``` -## Get GEM port status table +## Getting GEM port status table ```sh gtop -g e ``` @@ -78,7 +78,7 @@ To get the LAN Mode: ```sh onu lan_port_status_get 0 ``` -The `link_status` variable tells the current speed +The `link_status` variable tells the current speed: | Value (for `sgmii_mode` and `link_status`) | Speed | | ------------------------------------------ | ---------------------------------- | @@ -133,10 +133,11 @@ fw_setenv image1_version "YOUR_SW_VERSION_1" # Advanced settings -{% include alert.html content="Normally they are not necessary and it would be better not to touch them" alert="Note" icon="svg-warning" color="red" %} +{% include alert.html content="Changing these is normally not necessary and not changing them is a good idea" alert="Note" icon="svg-warning" color="red" %} ## Setting custom OMCI MIB file -You have to copy the MIB file to /etc/mibs and then run this command: + +Copy the MIB file to /etc/mibs, then run this command: ```sh fw_setenv mib_file_custom "YOUR_MIB_FILENAME" @@ -155,7 +156,7 @@ reboot # SFP EEPROM settings -{% include alert.html content="Normally they are not necessary and it would be better not to touch them" alert="Note" icon="svg-warning" color="red" %} +{% include alert.html content="Changing these is normally not necessary and not changing them is a good idea" alert="Note" icon="svg-warning" color="red" %} ## Setting SFP vendor name ```sh |