1 files changed, 120 insertions, 0 deletions
diff --git a/Linux/README.save b/Linux/README.save
new file mode 100644
index 0000000..b63888f
--- /dev/null
+++ b/Linux/README.save
@@ -0,0 +1,120 @@
+Heimdall (c) 2010 Benjamin Dobell, Glass Echidna
+http://www.glassechidna.com.au/products/heimdall/
+
+DISCLAIMER:
+
+    This software attempts to flash your Galaxy S device. The very nature of
+    flashing is dangerous. As with all flashing software, Heimdall has the
+    potential to damage (brick) your phone if not used carefully. If you're
+    concerned, don't use this software. Flashing ROMs onto your phone may also
+    void your warranty. I am not responsible for the result of your actions.
+
+
+
+These instructions are for Linux operating systems.
+
+Installing Heimdall from Source:
+
+    1. First make sure you have installed build-tools and pkgconfig.
+
+    2. Open a terminal and navigate to the directory you extracted Heimdall to.
+
+    3. Then enter the following commands to compile and install libusb-1.0:
+
+            cd libusb-1.0
+            ./configure
+            make
+            sudo make install
+            cd ..
+
+       If you have problems please consult http://www.libusb.org/        
+
+    4. Enter the following commands to compile and install Heimdall:
+
+            cd heimdall
+            ./configure
+            make
+            sudo make install
+            cd ..
+
+	    NOTE: You can use "checkinstall" instead of "make install" in order
+                  to generate a redistributable package.
+
+    5. If you're not installing from a package then run
+       Linux/install-udev-rules.sh to setup user-level permissions for libusb. 
+
+    6. Done
+
+
+
+Installing Heimdall Frontend from Source (Optional):
+
+    1. First make sure you have installed Qt 4.6 or above,
+       available from http://qt.nokia.com/.
+
+    2. Open a terminal and navigate to the directory you extracted Heimdall to.
+
+    3. Enter the following commands to compile and install Heimdall Frontend:
+
+            cd heimdall-frontend
+            qmake heimdall-frontend.pro
+            make
+            sudo make install
+
+       NOTE: You can use "checkinstall" instead of "make install" in order to
+      cd       generate a redistributable package.
+
+    4. Done
+
+
+
+Flashing Firmware with Heimdall Frontend:    
+
+    1. Fully charge your device (use the wall charger as it's faster).
+
+    2. Download a decrypted Samsung Galaxy S ROM and extract it to a directory.
+
+    3. If the ROM is provided as one of more archives (nested or otherwise),
+       extract them all to the same location.
+
+       NOTE: If you want to use the CSC then extract it last.
+
+    3. Open Heimdall Frontend.
+
+    4. Put your Galaxy S device into download mode.
+
+    5. For each file you wish to flash use "Browse" to select the file.
+
+    6. Press "Start".
+
+    7. Heimdall Frontend will display the progress and inform you when the
+       flash is complete.
+
+
+
+Flashing Firmware from Command Line / Terminal:
+	
+    1. Fully charge your device (use the wall charger as it's faster).
+
+    2. Download a decrypted Samsung Galaxy S ROM and extract it to a directory.
+
+    3. If the ROM is provided as one of more archives (nested or otherwise),
+       extract them all to the same location.
+
+       NOTE: If you want to use the CSC then extract it last.
+
+    4. Open a terminal and navigate to the directory where you extracted the
+       ROM files.
+
+    5. Type the following to list all the functionality Heimdall supports:
+
+            heimdall help
+
+    8. Use the instructions to manually enter a command with all the files you
+       want to flash.
+
+       Here is an example that does a full flash and repartition:
+		
+            heimdall flash --repartition --pit s1_odin_20100512.pit --factoryfs factoryfs.rfs --cache cache.rfs --dbdata dbdata.rfs --primary-boot boot.bin --secondary-boot Sbl.bin --param param.lfs --kernel zImage --modem modem.bin
+
+    9. Done